Skip links

Pigment vs Dye in Textiles: Which Should Your Mill Use?

Textile Printing

Pigment vs Dye in Textiles: Which Should Your Mill Use?

By Deven Shah, Indian Chemical Industries (ICI) · Ahmedabad, India · Updated November 2026

Quick answer

Use pigments when speed, flexibility across fibres and a simpler process matter most, and when your buyer accepts the hand feel and rub fastness a binder-fixed print gives. Use dyes when the fabric needs the deepest penetration, the softest feel or the highest wash and rub performance.

Many mills run both. The right choice depends on fibre, shade depth, end use and what your export buyer's compliance team will accept. Pigment printing is a major part of the market: industry estimates put it at roughly 45–60% of textile printing worldwide.

What is the difference between a pigment and a dye?

Pigments and dyes are the two basic colourants for textiles. The difference is how the colour attaches to the fabric.

Dyes bond with the fibre

Dyes are soluble. They dissolve in water, enter the fibre and bond to it chemically. Reactive dyes on cotton and disperse dyes on polyester are common examples. Because the colour becomes part of the fibre, dyed fabric usually keeps a soft hand and performs well in wash and rub tests. The trade-off is a longer process with fixation, washing off and effluent to treat.

Pigments sit on the fibre

Pigments are insoluble. They have no natural affinity for textile fibre, so they are applied as a fine dispersion and fixed on the surface with a binder. A pigment print system typically combines the pigment dispersion, a binder, a fixer, a thickener, emulsifiers and a softener. The colour is held in a thin film on the fabric, not inside the fibre.

Pigment vs dye: side-by-side comparison

Factor

Pigment printing

Dye printing (reactive, disperse)

Solubility

Insoluble; fixed with a binder

Soluble; bonds with the fibre

Fibre range

Cotton, polyester, blends and most substrates with one system

A specific dye class for each fibre type

Process

Print, dry, cure. Usually no wash-off

Print, fix (steam), wash off, dry

Sampling speed

Fast

Slower

Hand feel

Can feel stiffer; depends on binder

Generally softer

Rub (crock) fastness

Depends heavily on binder and curing

Generally stronger

Water and effluent

Lower process water

Higher process water and effluent load

Typical process cost

Lower

Higher

Performance varies by product, shade depth and process control. Treat the table as a starting point and test on your own fabric.

Where pigment printing wins

Fewer process steps

A pigment print is generally printed, dried and cured. Skipping steaming and heavy wash-off saves time, energy and water. For high-volume work this is the main reason mills choose pigments.

Fast sampling and shade changes

With a dispersion-based system you can sample and adjust shades quickly, which suits fashion cycles and small runs. Colour matching is done on the print paste, not through a long dyeing cycle.

One system across many fibres

Because pigments do not rely on fibre chemistry, the same colour system can be applied to cotton, polyester, viscose and blends. That simplifies inventory for mills printing mixed fabrics.

Where pigment printing falls short

Hand feel

The binder forms a film on the fabric. Too much binder, or a poorly chosen one, gives a stiff handle, especially in heavy, dark prints.

Rub (crock) fastness

This is the best-known weak point. Results depend on the binder, fixer, curing temperature and time, and pH. Poor curing is a common cause of colour rubbing off, so process control matters as much as the pigment itself.

Binder dependence

The binder is a core part of the system, and it carries environmental requirements too. Buyers increasingly ask for APEO-free and formaldehyde-free chemistry.

When dyes are the better choice

  • Deep, saturated shades where penetration and a soft feel are critical
  • Products worn next to skin or washed frequently, where wash and rub performance is the priority
  • Fabrics where a binder film would change the drape or breathability too much

What export buyers check before approving a colour system

If you supply brands in Europe or the Americas, the colourant's compliance paperwork often matters as much as its shade:

  • Chemical compliance: conformance to the ZDHC Manufacturing Restricted Substances List (MRSL). Conformance is assessed at levels 1, 2 and 3, with Level 3 giving the highest confidence. Read more on our ZDHC page.
  • Product certifications: such as Eco Passport and, for organic-fibre products, GOTS.
  • Documentation: a technical data sheet and safety data sheet for each product, plus certificate scope and validity.
  • Binder chemistry: APEO-free and formaldehyde-free declarations where required.

Ask your supplier which products are covered by each certificate, not just whether the company holds one. ICI's certifications are listed on our compliance page.

How to decide: five questions for your mill

  1. What fibre are you printing? Blends and mixed lots favour pigments. Single-fibre, premium goods may favour dyes.
  2. How deep is the shade, and how will the fabric be used? Dark, heavily washed items need more fastness testing.
  3. What do your buyers test for? Check their wash, rub and restricted-substance requirements first.
  4. How much water and energy can you spend? Pigment printing usually reduces both.
  5. How fast must you sample and deliver? Short lead times favour pigments.

If you are unsure, run a trial: print the same design with both systems on your actual fabric and test them to your buyer's standard.

Frequently asked questions

Is pigment printing cheaper than dye printing?

Process cost is usually lower because there is less steaming and washing. Total cost also depends on pigment loading, binder use and rework, so compare on a finished-metre basis.

Can pigments be used on polyester and cotton blends?

Yes. Because pigments are fixed by a binder, not by fibre chemistry, one system can print many fibres and blends.

Why does pigment-printed fabric sometimes lose colour when rubbed?

Usually the binder, fixer or curing was not right for the shade depth. Check binder type and amount, curing temperature and time, and pigment loading.

Do all pigment dispersions meet ZDHC requirements?

No. Conformance depends on the specific formulation, so ask for documentation per product.

Request a quote

Tell us your fibre, shade range, volume and export market, and our team will recommend a pigment or dye route and quote it.

Learn more about Indian Chemical Industries (ICI), a pigment and dye manufacturer based in Ahmedabad.

Sources